Spirit Week Paper Airplane Challenge

Fold a paper dart, compare two flights from one launch line, and record what changed. Includes a staff setup checklist and editable flight sheet.

Build
One paper dart
Test
Two flights
Included
Editable flight record

Fold one plane and compare two flights

Give each team one sheet of paper and one job: fold a dart, fly it twice and describe what changed. Use the same launch line and measure the forward distance to where each flight first touches the floor. A short flight is a result the team can record.

Use a staff-approved gym or another supervised space with a clear flight lane. A classroom with occupied desks is better used for folding and discussion. If you do not have a suitable launch area, choose the paper tower challenge for a tabletop alternative.

Prepare the launch lane

  • One rectangular sheet of paper and one flight record per team.
  • A permitted floor marker or existing line for the launch point.
  • A tape measure and an agreed unit, such as centimeters.
  • A clear landing area and a waiting place behind the line.
  • A staff signal for launch and a separate signal for retrieval.

Set up one lane and allow one flight at a time. Keep viewers behind the line or outside the flight path. A staff member checks that the lane is clear before each launch and signals when the plane may be collected. Pause if anyone enters the lane. Keep the tape measure out of the lane during flights.

For 24 students in teams of four, prepare six building sheets and six records. Two flights for each of six teams means 12 launch, measure and retrieval turns. If that queue is too long for your time slot, use one shared demonstration plane while groups predict and record the two results.

Make a simple paper dart

This fold adapts the opening steps from NASA Glenn’s dart lesson. Use the same paper size and type for the group. The spirit week version uses folds alone; the NASA lesson also describes optional finishing and a longer flight investigation.

  1. Place the rectangle with a short edge at the top. Fold it lengthwise to mark the middle, then open it.

  2. Bring both top corners in to meet the middle crease. Bring the resulting slanted edges in toward that crease again, making a narrow nose.

  3. Close the plane along the center crease so the folds sit on the outside. Fold each outer flap down to form a wing, leaving a strip below the wings to hold. Open the wings and check that they sit at similar angles.

Demonstrate one fold at a time or provide a partly folded sheet. Students can suggest a change, help crease, observe or record. No one needs to throw. The photos illustrate the dart shape and setup rather than showing a measured trial.

Measure the first landing, then change one detail

Flight 1: record a starting result

On the staff signal, the launcher sends the dart gently down the lane from behind the line. A spotter outside the lane notes where it first touches the floor. After the retrieval signal, mark that location and measure how far forward it is from the line, parallel to the lane. Ignore any slide after landing.

Flight 2: make one small revision

Change one thing, such as bending both rear wing edges up slightly by the same amount. Record the change before throwing. Use the same plane, launch line, direction, measurement rule and launcher if practical. Try to release it in the same way. Then record the second landing distance.

If a plane hits a wall, leaves the lane or lands where the spotter cannot identify first contact, mark the result “no reading.” Give a repeat only when staff can keep the lane clear and the schedule allows. Leave an unmeasured distance blank.

Compare the two observationsIn an invented example, the plane travels 240 cm, then 210 cm after a change. The second flight is 30 cm shorter. Throwing differences can also affect the result, so describe what happened in these two flights without claiming the fold always produces that result.

Keep the session moving

Try five minutes to explain and fold, a flight window sized to your group, and three minutes to compare and pack away. A single lane takes longer with more teams. Check how long one complete launch, measurement and retrieval takes before promising that all teams will fly twice.

Give waiting teams a job: sketch their proposed revision or predict whether they expect a longer, shorter or similar flight. Let students choose familiar roles such as folder, spotter or recorder, and use their usual communication supports. The inclusive planning guide offers more participation options.

End with one observation per willing group: “We changed ___ and our second flight went ___.” There is no need for a class distance ranking. If staff have chosen a team format, use the team names on the record sheets rather than adding decorations or weight to the planes.

Save the flight record and setup notes

Download the editable paper airplane flight record

The text sheet includes the two flight entries, revision note, lane checks and NASA folding reference. Copy it into a class document or put the two entries on scrap paper. Record the lane, launch and retrieval signals in the staff handoff if another teacher will lead it.

If the flight space becomes unavailable, switch to folding and comparing shapes at tables, or use a different activity from the indoor backup plan. Keep the two-flight record for a time when the lane is available.

Choose a theme for a shared activity

Browse ideas and prepare a simple class plan.